This troubleshooting guide is organized into 5 sections which are intended to help you operate, test and troubleshoot Series 94 Stabilized Antenna Syst ems. Should you find any errors, or have any suggestions, please call or fax your input to Sea Tel. ![]() Jan 1, 2000 - This manual describes the Sea Tel Model DAC-97 shipboard Tracking. The DAC-97 is an all digital version of Sea Tel's proven line of TAC-92. SCOPE This manual describes the Sea Tel Model 9797 C/Ku Band Stabilized Transmit/Receive antenna systems with unlimited azimuth and provides installation and operating instructions. Easy to maintain.4.
Refer to the appropriate Quick Start Operation guide for your system for routine operation. When you need to isolate a problem, st art with the Troubleshooting P rocedures section. Many problems are actually found to be an incorrect operator setting or parameter, rather than a component failure. Follow the procedures through Initial Power-up Operation, to functional Testing and finall y to Problem Scenarios or Troubleshooting Modules. If you have identified a specific failure, you may prefer to go directly to the appropriate Troubleshooting Module(s) to begin (refer to the Table of Contents). In using this troubleshooting guide you may be pointed from a procedure, test or problem to another section or to a troubleshooting module. You may also be directed from one troubleshooting module to another. Last updated 2018-08-22 11:24:20. Overview The purpose of this document is to detail the installation and configuration of a Sea Tel Antenna Controller Unit (ACU) for use with Uplogix Local Managers. Features • Supports DAC (ACU) software versions 4.10 and later Terminology Acronyms and abbreviations used in this document: • ACU – Antenna Controller Unit • DAC – Digital Antenna Controller • DacRemP – DAC Remote Panel • M&C – Managing and Controlling • PCU – Pedestal Control Unit Physical Connection There are two connection points from the Sea Tel ACU (M&C and NMEA) to the appliance. The M&C connection is used to interactively manage the Sea Tel ACU and PCU. The NMEA connection is used to collect GPS information in NMEA-183 format from the Sea Tel ACU. Both M&C and NMEA information may be retrieved from the M&C port. The NMEA port should be used when the M&C will be utilized for extended interactive user sessions so GPS coordinates can be collected without interruption. The M&C port on the Sea Tel ACU can be connected to the Uplogix Local Manager with standard CAT5 cables and DB-9 to RJ-45 adaptors. Stellar phoenix access repair serial. The M&C port requires a rolled cable and the NMEA port requires a straight through cable. Configuring the Port A few important items to note prior to configuration: • The default baud rate for the Sea Tel M&C port is 9600 on DAC 2202/2302/2200 series and 4800 on DAC 03/97 systems. The Uplogix appliance will need to be configured with the appropriate rate. • The default baud rate for the Sea Tel NMEA port is 4800. If this value has changed, the Uplogix appliance will need to be configured with the new rate. • The ACU’s Serial M&C port does not require a username or password, although the initialization routine will ask for them. Bypass this prompt by hitting the return key. Once the Sea Tel ACU is properly connected to the Local Manager, take the following steps to configure the port: Open a connection to the Uplogix appliance and navigate to the port you wish to initialize. Use the config init command to configure the port for use with the M&C port on the Sea Tel ACU. The make should be SeaTel and the OS DAC. Model and OS version are optional fields and will be populated automatically as part of the config init process. Press [Enter] when accepting default values. [admin@UplogixLM (port 1/3)]# config init --- Enter New Values --- description: []: Starboard Aft Antenna make: [native]: SeaTel model: []: os: []: DAC os version: []: management IP: []: Configure dedicated Ethernet port?
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |